Code Erreur Climatiseur Condor PDF Free Download

Code Erreur Climatiseur Condor PDF Download Info

If T2 < Tcool – 1°c Is Not Continuous For Four Seconds And The Compressor Operation Frequency > 50 Hz Is Not Continuous For Three Minutes, Within Five Minutes Of The Compressor Operation, The Air Conditioner Shall Turn Off, And An Error Code Shall Flash On The Led Indicator. This Shall Happen Three Times.

Code Erreur Climatiseur Condor PDF Free Download

Things That Shall Be Prepared For Use:

• Internal Printed Circuit Board; T2 Sensor • Refrigerant Additional

You Are Looking For The Steps To Follow When Your Air Conditioner Broke Down. In Most Cases, The Error Code Has The Solution To Your Problem.

While Error Codes, Denoted By Leds, Are Consistent Within The Brand For All Models, Navigation Through Them May Get Tricky Sometimes. If They Are Often Mentioned In Your Device’s Instructions, Do Not Be Afraid To Call A Repairman If You Can’t Handle Navigating.

Error Codes For Airton Air Conditioning

The Error Code E1/e2/e3/e7 Shows Faulty Temperature Or Outside Sensors. If Your Air Conditioner Is Still Under Warranty, Contact Customer Support; They Must Be Replaced. Error Number E5: There Could Be Overcurrent Resulting In The Outside Unit’s Poor Communication With The Computer. Have Your Gadget Inspected By An Expert.

Error Code E6: Problem With The Indoor Fan Motor. See If The Fault Will Be Rectified By A Simple Cleaning Or If A Replacement Part Is Required. Error Code P5:

Air Conditioner Evaporation Mechanisms Malfunctioning. Check Whether Your Appliance Is Dirty Or Whether Any Parts Need To Be Replaced. Error Codes P5/p6/p7: The Appliance Is Operating At Temperatures Out Of The Normal Range At The Condenser Or The Outside Unit.

Atlantic Air Conditioning Error Codes

Error Code A1: The Compressor Sensor Is In Protection Mode. It Has Gone Into Protection Mode Due To A Strange Temperature Anomaly. This Switchover Often Results From A Refrigerant Leak Or Blocked Filter. There Was A Communication Problem Between The Interior And Outside Units, Which Caused The Error Code 00:11 Er. After Two Minutes, Turn Your Air Conditioner On Again.

Call A Professional If The Error Persists. Error Number 21.1: A Failure In Communication Between The Secondary Remote Control And The Air Conditioner. Check The Operation Of The Latter And Replace The Batteries If Necessary.

The Blocked Filter Is Signaled By Error Code 24.1. To Wash The Filter And Replace It In Case Of Breakage, Assemble Your Appliance Reversely. Error Codes 42.1 And 42.2 Show The Failure Of Communication With The Outside Unit. After Two Minutes, Plug In The Appliance And Turn It On. If It Still Doesn’t Work, Call A Pro.

Carrier Air Conditioning Error Codes

Error Code E1: There Is A Communication Malfunction Between The Indoor Unit And Outdoor Unit. Check Your Appliance’s Wiring And Connections. Contact An Expert If The Electronic Card Is Faulty. Error Code Df: Outside Unit Defrosting Is Necessary. The Temperature Is Self-adjusting By Blowing Hot Air From The Appliance; Sometimes It Takes A Bit Longer Than Usual. The Error Code E6 Will Display The Electrical Malfunction In The Reversing Valve.

Replace The Portion Affected. Error Code P6 Will Indicate A Pressure Problem Of The Indoor Unit. Electrical Malfunction Of The Appliance May Cause It. Temperature Sensors Are Indicated By The F04/f06 Error Codes. It Is Either An Open Circuit Or A Short Circuit. Have The Air Conditioner’s Electrical System Checked.

Condor Air Conditioning System Fault Codes

Error Code E5 Overcurrent At The Compressor Protection Level. This Is An Electrical Fault, Replace The Culpable Component If Need Be. Error Code E8 Fan Protection At The Indoor Unit. If It Is Dirty Or Faulty, Clean Or Replace The Sensor.

The Error Code F1 Indicates A Malfunction Of The Sensor At The Evaporation Level. Replace The Malfunctioning Sensor And Check If The Malfunction At The Evaporation Level Is Resolved. The Error Code F4 Indicates A Malfunction Of The Sensor Of The Outdoor Unit. Replace The Malfunctioning Sensor And Have It Checked By The Unit.

Error Codes For Daikin Air Conditioners

The Unit Has Too Little Refrigerant. Check Whether There Is Enough Liquid In The Appliance And Whether The Pipes Are Not Blocked With The Stop Valve Shut. Error Code A5: Frost Protection In Cooling Mode, Or Pressure Is Too High In Heating Mode. This Means That Either An Interior Unit Air Filter Is Blocked Or It Is A Result Of A Short Circuit Of The Temperature Exchanger.

Error Code E3: Appliance Pressure Is Too High. This Might Be Due To Blocked Refrigerant Pipes, Fault Pressure Switch, Or Even Filter Plug. F3/j3 Error Code: Abnormal Temperature Of The Discharge Pipe. Cleanliness Of The Pipe. Check Electrical Connections Of Any Faulty Connectors; Clean The Utery If It Is Dirty. Jc Error Code Indicates Low-pressure Sensor Breakdown. Replace The Sensor And Ensure That The Electronic Board Of The Outdoor Unit Is Working Well.

Lg Air Conditioning Fault Codes

Ch07 Error Code: Hot/cold Split. The Appliance Is In Both Heat And Cold At The Same Time. Switch The Device Off, Restart It, And Set It Back To The Desired Setting Using The Remote. Ch10 Error Code: The Power Source Of The Indoor Unit Motor Is Faulty. Check The Connection Of The Latter To The Connecting Cable And The Electronic Board.

Replace The Fan Motor If Necessary. The Error Number Ch21 Overcurrent Detected In The Appliance. Check The Connections At The Compressor, The State Of The Electrical Resistors And Possible Humidity In The Circuits. Error Code Ch46 Indicates The Problem In The Compressor Suction Pipe Sensor.

Do An Electrical Diagnostic That Rules Out The Malfunctioning Of An Internal Circuit, A Soldering Mistake, Or Even A Short Circuit. Ch67 Error Code: Condenser Fan Blocked. Verify That Fans Are Not Blocked Or Dirty.

Qlima Air Conditioning Error Codes

Error Code E1: Electrical Failure Of Outdoor Unit. The Issue Usually Comes From The Electrical Connection Mistake. Otherwise, The Electronic Card In The Machine Has To Be Changed. P1 / P2 / P3 Error Code: This Error Code Indicates An Electrical Issue Related To The Compressor Level.

Unplug And Replug Your Appliance After Ten Minutes. If The Problem Persists, Contact Customer Care Or An Expert. Error Code F1 / F2 / F3: Electrical Malfunction Of The Sensor. Run A Diagnostic To Find Out What Is Wrong, Then Replace The Component That Is Affected.

Midea Air Conditioning Fault Codes

Error Code E1 Indicates There Is A Communication Malfunction Between The Interior And The Outdoor Devices. Check The Appliance Electrical Connections Together With The Electronic Card’s Functioning Ability. Error Code E2 Indicates That There Is An Abnormality With The Ambient Temperature Sensor. If The Reset Of The Air Conditioner Does Not Work, Replace The Sensor With A Similar Part.

Error Code E5 Indicates A Problem With The Water Pump Temperature Sensor. This Error Could Be Due To Its Failure To Work Correctly In The Power Surge Of The Appliance. This Would Lead To Overheating. The Error Code Ec Indicates The Failure Of A Refrigerant Leak Detection System.

Check The Condition Of The Liquid Container And Pipework. Fault Code F0/f1/f2—issues With The Functioning Of The Automated Lifting Panel. Check If The Panel Remained Open, Or If It Has Become Distorted From External Factors.